Galoot Central
Home arrow Image Central
Saturday, 17 February 2018
Galoot Image Central - Home > User galleries

Galoot Image Central

Pics from the Porch


Home :: Login
Album list :: Last uploads :: Last comments :: Most viewed :: Top rated :: My Favorites :: Search

Home > User galleries


mjd
3 album(s)
20 file(s)

Ken Cutting
2 album(s)
15 file(s)

Charlie Rodgers
8 album(s)
33 file(s)

nicknaylo
5 album(s)
344 file(s)

Gary K
5 album(s)
45 file(s)

dlarue
17 album(s)
633 file(s)

Charlie Driggs
9 album(s)
176 file(s)

jimob
5 album(s)
23 file(s)

PeterH
1 album(s)
5 file(s)

jonjunk
7 album(s)
18 file(s)

Peter.Robinson
16 album(s)
65 file(s)

Sanger
1 album(s)
4 file(s)
137 users on 12 page(s) 1

Random files - User galleries
P1100023.JPG
P1100023.JPGCamphor laurel bowl165 viewsExcellent figure in wood from Tasmaniajonjunk
IMG_5224.jpg
IMG_5224.jpgSide Rebate Dismantled87 viewsPeter.Robinson
Image-7C82413A64B411D8.jpg
Image-7C82413A64B411D8.jpgVeneer saw70 viewsA hand made veneer saw.Oldmillrat
Tools_018.jpg
Tools_018.jpgStanley #4 type 11 bottom24 viewssbussell
PICT1218.jpg
PICT1218.jpgChariot plane from Shepherd kit102 viewsI needed to clean up all of the metal parts quite a bit so I took the opportunity to add the double urn design to the brass bridge.gstucker
Brass_pintles_anchor_the_ogee_tester_frame_and_the_frame_cross_pieces_at_each_end.JPG
Brass_pintles_anchor_the_ogee_tester_frame_and_the_frame_cross_pieces_at_each_end.JPG202 viewsThe tester frame can be used or not, but the head and foot cross pieces and pintles must be used to keep the bed posts from folding up.Sgt42RHR
Sanpaper_cutter.jpg
Sanpaper_cutter.jpgSandpaper cutter 261 viewsThis device is my sandpaper cutter. I use it to cut sandpaper into halves and quarter sheets. There is a coarse hacksaw blade in front which acts as the cutting blade. The back has a hinged block which puts the paper into the correct position to cut either size.
This is simple to make, and it makes life a lot easier when you need to cut sandpaper.
Oldmillrat
LodiSawVise3.jpg
LodiSawVise3.jpgLod Saw vise clamping cam handle 29 viewsnicknaylo

Last additions - User galleries
joinery_small.jpg
joinery_small.jpgjoinery3 viewsyou can see the peg through the M&T jointdlarueFeb 13, 2018
chair1.jpg
chair1.jpgfinials, finally5 viewsMy dubious attempt at the finials.
I may re-turn these before final assembly.
dlarueFeb 11, 2018
chair2.jpg
chair2.jpgpile of turnings5 viewshere is the pile of turnings from the pole lathe. Still need to finish a bunch of them, they are just rough turned at this point.dlarueFeb 11, 2018
2018_01_24_3109_GClausS.jpg
2018_01_24_3109_GClausS.jpgGalootaclaus 2017 overview61 viewsSchwartzJan 28, 2018
2018_01_27_3110_GClausSS.jpg
2018_01_27_3110_GClausSS.jpgGalootaclaus 2017 detail54 viewsrabbet plane ( rebate Jeff ) awaiting 1st assignmentSchwartzJan 28, 2018
Cabinet_front.jpg
Cabinet_front.jpgCabinet front closed132 viewsThe carcase and frame is all made from a single 40 year old air dried Appalachian black walnut board. The two panels are resawn and book matched from a single off cut of Indiana black walnut saved from the burn pile. The finish is four coals of 1-pound cut amber shellac, well rubbed out with 0000 steel wood after each coat. The whole is finished with a coat of Liberon brown paste wax. The knob is an ebony violin tuning peg. Closure is achieved by a rare earth magnet and a steel screw.Sgt42RHRJan 08, 2018
cabinet_open_empty.jpg
cabinet_open_empty.jpgCabinet open and empty116 viewsThis is the inside showing the poplar back and the reverse of the book matched front panels. The hangers are 1 1/2 inch Tremont cut finishing nails set in pre-drilled holes with a dab of CA glue.Sgt42RHRJan 08, 2018
Cabinet_open_full.jpg
Cabinet_open_full.jpgcabinet open full140 viewsHere are some of the reasons I built this cabinet which is attached to wall studs just over and to the side of the dresser.
Sgt42RHRJan 08, 2018

Member Login
 
© 2018 Galoot Central
Joomla! is Free Software released under the GNU/GPL License.
View Jim Esten's profile on LinkedIn