My Workbench |
 |
| TITLE |
+ |
- |
| FILE NAME |
+ |
- |
| DATE |
+ |
- |
| POSITION |
+ |
- |
|
|
IMG_1025.JPGEnd Vise Close up208 viewsHere's a pic of the old Columbian quick action vise that serves as the end vise.TRexF16
|
|
IMG_1054.JPGDeadman 3: Finished236 viewsHere is the finished deadman amid all the shavings from flattening the topTRexF16
|
|
IMG_1033.JPGDeadman 2: 214 viewsDeadman installed but no linseed oil on it yet. The top hole is at the correct level that the top of a 3/4 inch dog in the deadman is dead even with the top of the vise screws on the face vise. So if I clamp a long narrow board I'll get even support from the deadman and clamping from the face vise and a holdfast in the right leg.TRexF16
|
|
IMG_1031.JPGDeadman 1: Layout258 views[Galoot In Training] Taylor and I lay out the curve for the waist of the deadman with an old set of Stanley #4 Trammel points. TRexF16
|
|
IMG_1043.JPGChip Repair 5197 viewsFinished repair. It turned out I didn't get as good a grain and color match as I'd hoped but it still looks a lot better than before.TRexF16
|
|
IMG_1036.JPGChip repair 1194 viewsWhile I had the top upside down on the scrounged table, I used its end dog hole along with a holdfast to hold the legs and stretchers while I mortised and planed them. When I flipped the top over to mount it on the finished base I saw there had been some chipping due to the lack of any countersinking or chamfering around the hole, so I needed to fix it...TRexF16
|
|
IMG_1042.JPGChip Repair 4201 viewsTHe replacement piece held for gluing with a holdfast.TRexF16
|
|
IMG_1041.JPGChip repair 3189 viewsI cut a recess with a fitted replacement piece. It is undercut a bit (like a dovetail) at the part of the slot opposite the hole.TRexF16
|
|
IMG_1038.JPGChip repair 2189 viewsI sorted through the offcuts from the top hoping to find a candidate with matching grain and color. There is a lot of variance in the maple in my top, as this photo shows.TRexF16
|
|
IMG_1061.JPGVise problem 2358 viewsThe backing slabs could move up to 1/8 inch under offset clamping force because the 3/8 inch bolts run through 1/2 inch holes. No way can 3/8 inch bolts resist the clamping force of 1 1/2 inch acme thread steel vise screws! I decided to fix this problem by boring holes for tight-fitting dowels which will prevent any movement. Here I am boring the 3/4 inch holes from underneath the top for the pegs. The holes pass through the slabs which back the face vise and well up into the benchtop itself. 3/4 inch maple dowels will be driven through these holes and up into the benchtop.TRexF16
|
|
IMG_1027.JPGVise problem 1281 viewsThis shot taken while fitting the screws to the face vise shows the basic configuration of the face vise itself and the two backing slabs which are bolted top to bottom through the benchtop. Each backing slab has two 3/8 inch bolts running through them. Nevertheless, I still found that if I clamped a board in the face vise, and it only bore against the top and the face vise, or the leg and the face vise, but not the backing slabs, I could easily put enough force on it to pull the slabs out of alignment.TRexF16
|
|
IMG_1051.JPGTop flattening 2243 viewsThis job was made more difficult by lack of a really fine straight-edge. I have a three foot aluminum "garden variety" staight edge, which helps a bit, but so wish for a real, no kidding high precision four foot (or more) Starrett or one of equal quality. Santa, if you're listening...TRexF16
|
|
|
|
Image Central 
